| HP MSA2000 CLI Help |
|
HP MSA2000
# help To get detailed help on any commands, type 'help <full command>' (e.g. help show disks).
abort create - Stops the create vdisk operation for a
abort scrub - Aborts the scrub vdisk operation for specified virtual disks abort verify - Aborts the verify vdisk operation for specified virtual disks abort volumecopy - Aborts copying a volume alias - Shows, creates, or deletes aliases for the current CLI session clear
clear
clear expander-status - Note: This command should be used only by service technicians, or with the advice of a service technician convert master-to-std - Converts a specified master volume into a standard volume convert std-to-master - Converts a standard volume to a master volume create host-wwn-name - Creates an entry for a host world wide port name (WWPN) and associates a nickname with the entry create iscsi-host - iSCSI only create master-volume - Creates a volume on a specified virtual disk, enables the volume for snapshots, and associates it with an existing snap pool create schedule - Schedules a task to run automatically create snap-pool - Creates a snap pool volume to use for snapshot data create snapshots - Creates a snapshot of each specified master volume create task - Creates a task that can be scheduled create user - Creates a new user profile create vdisk - Creates a virtual disk using the specified RAID level, disk drives, and optional vdisk spares create volume - Creates a volume on a virtual disk delete all-master-volumes - Deletes all master volumes associated with a snap pool delete all-snapshots - Deletes all snapshots associated with a specified volume, which can be a snap pool or master volume delete global-spare - Removes one or more disk drives from the pool of global spares delete host-wwn-name - Deletes the nickname associated with a host world wide port name (WWPN) delete iscsi-host - iSCSI only delete master-volume - Deletes a master volume delete schedule - Deletes a specified task schedule delete snap-pool - Deletes a snap pool delete snapshot - Deletes a snapshot volume delete snapshot-write-data - Deletes the modified portion of a snapshot volume delete task - Deletes a specified task delete user - Deletes a user profile delete vdisk - Deletes one or more virtual disks, disassociates all disk drives that are assigned to the virtual disks, and unmaps all volumes of the virtual disks from all host channels delete vdisk-spare - Removes one or more spare disk drives that are assigned to a specified virtual disk delete volume - Deletes a volume exit - Log off and exit the CLI session expand master-volume - Alias of expand volume expand snap-pool - Expands a snap-pool volume by a specified size expand vdisk - Adds disk drives to a virtual disk expand volume - Expands a standard volume or snap-pool volume by a specified size map volume - Creates a mapping whose settings override a volume's all-hosts mapping ping - Tests communication with a remote host rescan - This command forces rediscovery of attached disk drives and enclosures reset host-channel-link - Issues a loop initialization primitive (LIP) from specified controllers on specified channels reset snapshot - Deletes the data in a snapshot and resets it to the current data in the associated master volume restart - Restarts the storage
restore defaults - Note: This command should only be used by service technicians, or with the advice of a service technician rollback master-volume - Rolls back (reverts) the data on a master volume to the data that exists in a specified snapshot scrub vdisk - For specified RAID 3, 5, 6, and 50 virtual disks, this command verifies all parity blocks set auto-write-through-trigger - Sets the trigger conditions that cause the controller to change the cache policy from write-back to write-through set cache-parameters - Sets cache options for a specific volume, or the cache redundancy mode for a dual-controller storage system set cli-parameters - Sets the CLI timeout, the output characteristics of the show commands, and the way that the system handles some errors set controller-date - Sets the date and time for each management controller and then updates the date and time for each RAID controller set debug-log-parameters - Note: This command should only be used by service technicians, or with the advice of a service technician set drive-parameters - Selects a global disk Self-Monitoring Analysis and Reporting Technology (SMART) setting set expander-fault-isolation - Note: This command should be used only by service technicians, or with the advice of a service technician set expander-phy - Note: This command should be used only by service technicians, or with the advice of a service technician set global-spare - Designates spare disk drives that can be used by any virtual disk set host-parameters - FC and iSCSI only set host-port-interconnects - Enables or disables the internal connection between FC host port pairs set host-wwn-name - Sets the nickname of an HBA entry for a host world wide port name (WWPN) set iscsi-host - iSCSI only set job-parameters - Sets parameters for background scrub, partner firmware upgrade, and other jobs set led - Changes the state of drive module or enclosure LEDs to help you locate devices set
set password - Sets a user's password for system interfaces (such as the CLI) set prompt - Sets the prompt for the current CLI session set protocols - Enables or disables management services and protocols set snap-pool-policy - Sets the recovery policy that determines the action taken when a specified snap pool's error and critical threshold levels are reached set snap-pool-threshold - Sets the percentages of snap-pool space used that trigger the warning and error threshold policies set snmp-parameters - Configures SNMP notification of events set system - Sets the name, contact person, location, and description for a system set user - Changes a user's level, type, and interface access set vdisk - Sets the name and owning controller for an existing virtual disk set vdisk-spare - Designates spare disk drives that can be used by a specific virtual disk, and sets the disk drive status to VDISK SP set volume - Changes the name of a volume show auto-write-through-trigger - Shows the system's write-through trigger settings show cache-parameters - Shows cache settings for the storage system and optionally for a specified volume show channels - Shows information about channels on both controllers show cli-parameters - Shows the current CLI settings show configuration - Shows system configuration information show controller-date - Shows the system's current date and time show debug-log - Note: This command should only be used by service technicians, or with the advice of a service technician show debug-log-parameters - Note: This command should only be used by service technicians, or with the advice of a service technician show disks - Shows information about disk drives in the controller enclosure and any attached drive enclosures show drive-parameters - Shows the SMART setting show enclosure-status - Shows the status of system enclosures and their components show events - Shows events for an enclosure, including events from each management controller and each RAID controller show expander-status - Shows diagnostic information relating to SAS expander controller physical channels, known as PHY lanes show frus - Shows information for all field-replaceable units (FRUs) in the controller enclosure and in any attached drive enclosures show host-maps - Shows mapping information for volumes that are mapped to a specified host or to all hosts show host-parameters - Shows information about host channels on both controllers show host-port-interconnects - Shows the status of the internal connection between FC host port pairs show host-wwn-names - Shows the current list of FC host world wide names (WWNs) show inquiry - (For service techs only) Shows inquiry information for each controller module show iscsi-hosts - iSCSI only show job-parameters - Shows parameters for background scrub, partner firmware upgrade, and other jobs show license - Shows whether a license key is installed and information about licensed features show master-volumes - Shows information about master volumes associated with a specified controller or snap pool show network-parameters - Shows the network settings for each RAID controller show ntp-status - Shows the status of the use of Network Time Protocol (NTP) in the system show port-wwn - FC only show protocols - Shows which management services and protocols are enabled or disabled show redundancy-mode - Shows the redundancy status of the system show schedule-details - Shows information about a specified task schedule show schedules - Shows configured task schedules show sensor-status - Shows the status and current values reported by environmental sensors in each controller module and power module show shutdown-status - Shows whether the RAID (storage) controllers are shut down show snap-pools - Shows information about snap pools owned by a specified controller or both controllers show snapshots - Shows information about snapshots for a specified controller, master volume, or snap pool show snmp-parameters - Shows current settings for SNMP notification show system - Shows information about the system show task-details - Shows details of a configured task show tasks - Shows configured tasks show users - Shows configured user profiles show vdisks - Shows information for all or specific virtual disks show volume-maps - Shows mapping information for a specified volume or for all volumes show volumecopy-status - Shows information about in-progress volume copy operations show volumes - Shows volume information for all or specified virtual disks shutdown - Cleanly shuts down the RAID controller in either or both controller modules stty - Sets and shows terminal information trust - Enables an offline virtual disk to be brought online for emergency data collection only unmap volume - Removes an explicit mapping whose settings override a volume's all-hosts mapping verify vdisk - For specified RAID 3, 5, 6, and 50 virtual disks, this command verifies all parity blocks versions - Shows the hardware and software versions for each controller module volumecopy - Copies a snapshot or a master volume to a new standard volume
|
